Casio EX-292 Spezifikationen

REX-Z1000MAY. 2006(without price) Refer to the page 18 after changing the main PCB.INDEX

— 8 —2. How to restore the firmware1. Prepare the firmware restoration program and change its name as follows;rom800_060512.lbn 씮 titan.binNOTE: This

— 9 —3. To install the firmwareInitially, firmware is not installed in the PCB supplied by the parts center.Install the firmware into the PCB after re

— 10 —ADJ TOOL IntroductionMake sure to perform the adjustment by the USB ADJ Tool “adj03SSAW.exe” when replacing the lens unitor the PCB.Here the ne

— 11 —7) Check “Designate the place to search”, designate the place which contains “inf” file in the driver bypressing “Reference” button, and then pr

— 12 —2. How to use ADJ Tool when replacing Lens unitMake sure to perform the following procedure after replacing the lens.A floppy disk with the lens

— 13 —3. How to use ADJ Tool when replacing MAIN PCBFirmware is not installed in spare parts.1 Enter the TEST mode.1. Turn the power on while pressing

— 14 —VCOM DC ADJUSTMENT PurposeReadjust the VCOM value to minimize the flicker of the LCD after replacing the LCD or the main PCB. Necessary tools1

— 15 — Procedure1. Camera settinga) Turn the power on while pressing “BS” and “UPPER”.After pressing “DOWN” key twice, press “DISP” and “MENU”.Selec

— 16 —3. Measurementa) Connect S2281-01 to the camera’s LCD monitor (see below).AC Waveforms appear on the monitor screen of the oscilloscope.* Change

— 17 —THE COUNTERMEASURE FOR "SYSTEM ERROR"System error may occur when the battery is removed while data is written to the internal memory.

CONTENTSSPECIFICATIONS ...

— 18 —RESETTING THE PLACE OF DESTINATIONWhen the main PCB is replaced, the setting of the destination will be changed, therefore resetting is required

— 19 —DISASSEMBLY* Make sure to use correct screws when assembling sincethere are several kinds of them.It is a good idea to sort them as shown in the

— 20 —3. Remove the rear case assy.4. Remove the center case (A) and the power button.Note: Make sure not to lose the power button.5. Remove the keypa

— 21 —7. Remove two screws and then remove the front panel assy.Note: Discharge the strobe condenser. Removing the LCD8. Remove two screws and then r

— 22 —11. Remove the LCD. * Fixed with double-sided tape. Removing the key FPC12. Release the connector lock and remove the FCP.13. Remove the key FP

— 23 — Removing the strobe assy14. Release the connector lock and remove the FCP.15. Unsolder to remove two lead wires.16. Remove two hooks, and then

— 24 — Removing the mail PCB and the bottom sub assy18. Release the connector lock and remove two FCP.19. Remove four screws.Screw (S3)Screw (S3)Scre

— 25 —22. Remove the bottom sub assy.23. Remove the speaker.* Fixed with double-sided tape. Removing the lens unit.24. Remove two hooks, and then rem

— 26 —ASSEMBLY Assembling the lens unit1. Set the lens unit and fix it with three hooks.<hook locations> Assembling the speaker2. Set the lens

— 27 — Assembling the main PCB and the bottom sub assy3. Set the connector plate.Connector plate4. Set the main PCB.

— 1 —SPECIFICATIONSImage Files Format Snapshots: JPEG (Exif Ver.2.2); DCF (Design Rule for Camera File system) 1.0 standard;DPOF compliantMovies: Moti

— 28 — Assembling the buttery box assy5. Set the connector plate.<hook location>* Place two FPCs above.6. Fix it with four screws.NGNGScrew (S3

— 29 —7. Insert two FPCs.Lead wire (red)Lead wire (black)Lead wire (gray)Lead wire (black)Lead wire (red)8. Solder five lead wires.* Make sure to plac

— 30 — Assembling the key FPC10. Set the key FPC.* Positioning guides11. Insert one FPC.* FPC should be placed under the lead wires.

— 31 — Assembling the LCD12. Lead the FPC through the buttery box clearance.13. Fix the LCD with a double-sided tape and insert one FPC.14. Solder to

— 32 — Assembling the clump board15. Set the clump board.* Do not nip the lead wires.16. Fix with two screws. Assembling the case17. Set the front c

— 33 —19.Set the center case (B).20.Set the strap.21. Set the rear case.22. Fix it with five screws.* Do not nip the lead wires.23. Set the power butt

— 34 —EXPLODED VIEW4877965101116182019211715121314S1S2S1S2S3S2S3S1S3S3S4S5S12422262521232731282930233223S3

— 35 —PARTS LISTN Item Parts Code Parts Name Specification QTY Price Code R RemarkN 1 10242103 BOX ASSY/BATTERY RJK509022*001V02 1 CN 2 10241458 TAPE/

— 36 —N Item Parts Code Parts Name Specification QTY Code R RemarkACCESSORIESN - 10243983 CD ROM CK800DCA01R1CN - 10242037 AV CABLE AV-K800-BK151C- 10

— 37 —PRINTED CIRCUIT BOARDMAIN PCB (TOP VIEW)FU101FU100

— 2 —Delete 1 file; all files (with memory protection feature)Effective Pixels 10.1 millionImaging Element 1/1.8 square pixel primary color CCD (Total

— 38 —MAIN PCB (BOTTOM VIEW)

— 39 —SCHEMATIC DIAGRAMSMAIN PCB (1/3)225PSINKINTBVBUSFOUTWATCHPSCKRESETBPSRDYADPINBATTEMPPSRSTBPSOUTSHUTTER2MONOOUTKIN4VA_STBYPOWSWVIDEOVOUTVOUTDPLUS

— 40 —MAIN PCB (2/3)222222224444IRIS0IRIS1MT_RESETF_HOME_LEDMCKOZ_ENC_DETCCLKMT_SCLKCSNMT_STBPDNMT_DATACDTIZOOM0SDTIFOCUS0SDTOIRIS2LRCKIRIS3BICKMONOOU

— 41 —MAIN PCB (3/3)344ADPINTHPWCTL0PWCTL5PWCTL5PWCTL5BL-PWMBLONPWCTL1PWCTL1PWCTL2PWCTL3PWCTL4BLLEDKBLLEDACHGVCCVCC1-1VCC1-0GNDD100RSX101VA-3012P100 B

CASIO COMPUTER CO.,LTD.Overseas Service Division 6-2, Hon-machi 1-ChomeShibuya-ku, Tokyo 151-8543, Japan

— 3 —• Battery: NP-40 (Rated Capacity: 1300 mAh)• Recording Medium: SD memory card• Measurement Conditions*1 Number of Shots (CIPA)In accordance with

— 4 — Rechargeable Lithium Ion Battery (NP-40)Rated Voltage 3.7 VRated Capacitance 1300 mAhOperating Temperature 0 to 40°C (32 to 104°F)Dimensions 38.

— 5 —BLOCK DIAGRAM+–Lens UnitPENTAX 3XMotor FPCConnector23PINMOTOR-drLV8054LPLCD/BL UNIT2.8" WIDE LCD7-LED BLKEY-FPCConnector45PINConnector14PINC

— 6 —TEST MODENote: Never perform the menu items unless otherwise instructed. Doing so may cause destruction ofthe data inside, which will make the ca

— 7 —PROGRAM VERSION UPGRADING1. To update the firmware version1. Prepare the memory card which contains the firmware for EX-Z1000 in the root directo