Casio MZ-X500 Bedienungsanleitung

MZ-X300/MZ-X500MIDI ImplementationCASIO COMPUTER CO., LTD.ContentsI Overview 51 Product Configuration as a MIDI Device 51.1 System Section . . . . . .

Receive Receipt changes the mixer part volume.7.6 Pan (0AH)Message Format: BnH 0AH vvHn: MIDI Channel Numbervv: Value(Note1)Note1: For information abo

Received values and parameter setting values The range of the value of each DSP Parameter 7array element depends on the selected DSP or array number.

see 、26.3 Sustain Pedal Setting Value Table、 in 、VII SettingValues and Send/Receive Values.、• Timbre Type: DrumThe received message does not affect sou

7.13 Filter Resonance(47H)Message Format: BnH 47H vvHn: MIDI Channel Numbervv: ValueReceive Receipt changes the resonance intensity.7.14 Release Time

7.17 Vibrato Rate (4CH)Message Format: BnH 4CH vvHn: MIDI Channel Numbervv: Value (Note1)Note1: For information about the relationship between setting

7.21 High Resolution Velocity Prefix (58H)Message Format: BnH 58H vvHn: MIDI Channel Numbervv: ValueTransmit Sends the lower seven bits of 14-bit Veloc

7.25 NRPN (62H,63H)Message Format: BnH 62H llH (LSB)BnH 63H mmH (MSB)n: MIDI Channel Numberll: LSB Valuemm: MSB Value7.25.1 Part EnableMessage Format:

Parameter MSB LSB NotesLayer On/Off 5XH 00H Note1Octave Shift 5XH 01H Note2Pitch LFO Depth 5XH 02HFilter LFO Depth 5XH 03HAmp Volume 5XH 04HAmp Pan 5X

7.26.2 Fine TuneMessage Format: BnH 64H 01HBnH 65H 00HBnH 06H mmHBnH 26H llHn: MIDI Channel Numbermm: MSB Valuell: LSB ValueTransmit Sent when the fine

7.28 Reset All Controllers (79H)Message Format: BnH 79H 00Hn: MIDI Channel NumberTransmit Sent when MIDI send related settings are changed.Receive Rec

7.19 Vibrato Delay (4EH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147.20 Portamento Control(54H) . . . . . . . . .

8 Program ChangeMessage Format: CnH ppHn: MIDI Channel Numberpp: Program Number (Note1)Note1: For details about the relationship between the program n

When Stage Set.Chg NRPN is enabled by Instrument settings, number switching by bank select andprogram change is ignored. For details about stage setup

Part IIISystem Message11 Active SensingMessage Format: FEHTransmit Sent periodically when the MIDI sync mode is master.Receive Once this message is re

Transmit Sent when the Master Volume is changed.Receive Receipt changes the Master Volume.12.1.2 Master Fine TuningMessage Format: F0H 7FH ddH 04H 03H

12.1.6 Chorus TypeMessage Format: F0H 7FH 7FH 04H 05H 01H 01H 01H 01H 02H 00H vvH F7Hdd: Device IDvv: Value(Note1)Note1: For information about the rel

12.2.2 GM System OffMessage Format: F0H 7EH ddH 09H 02H F7Hdd: Device IDReceive Receipt changes the sound source setting to the Instrument presetting.1

Part IVInstrument-Specific System ExclusiveMessages13 FormatThis section explains the format of the Instrument-specific System Exclusive Messages. See “

13.3.3 MOD : Model IDFormat: MSB 00010111B (17H)LSB 00000010B (02H)These two successive bytes (MSB, LSB) indicate the MZ-X300/MZ-X500 model ID.13.3.4

13.3.7 mem : Memory Area IDFormat: 0mmmmmmmBSpecifies the memory area that is the object of the parameter transfer. The following are defined forthis In

2-dimension array block [index1][index0]Value Meaning00jjjjjjjiiiiiiiB 0000H00lllllllkkkkkkkB 0000H00nnnnnnnmmmmmmmB index100pppppppoooooooB index03-d

17 Tone Parameter 3217.1 DSP Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3217.2 LFO Parameter . . .

13.3.13 data : Parameter DataIndividual Parameter TransferFormat: index0 0dddddddB (0eeeeeeeB) (0fffffffB) (0gggggggB) (0hhhhhhhB)index1 0dddddddB (0e

15 Casio General System Exclusive15.1 FormatMessage Format: F0H 44H 7EH 7FH iiH ccH ... ssH ... ppH ... ddH ... F7Hii: Device ID (0x00...0x7F)cc ...:

Part VParameter ListThis section explains the parameters that actually can be transferred by the Instrument.16 Using the Parameter List• Parameter fiel

17.2 LFO ParameterThese parameters configure tone LFO settingsParameter ID R/W Block Size Array Min-Def-Max DescriptionPitch LFO Wave 0034 R/W 55-0:0 4

17.5 ToneBlock Parameter17.5.1 Basic ParameterThese parameters configure basic tone settings.Parameter ID R/W Block Size Array Min-Def-Max DescriptionN

19.1.1 Basic ParameterThese parameters configure basic settings for each drum tone instrument.Parameter ID R/W Block Size Array Min-Def-Max Description

Parameter ID R/W Block Size Array Min-Def-Max DescriptionChorus Send 000B R/W 6-0:Key # 7 01 00-00-7F 0 - 127Reverb Send 000C R/W ↑ 7 01 00-28-7F 0 -

Parameter ID R/W Block Size Array Min-Def-Max DescriptionOctave Shift 0011 R/W 3 01 02-04-06 -2 - 0 - +2Key Follow 0012 R/W 8 01 00-C0-FF -128 - 0 - +

21 Split Parameter21.1 Wave Split Parameter (x16split)Parameter ID R/W Block Size Array Min-Def-Max DescriptionKey Low 001D R/W 3-0:Split 7 01 00-00-7

Part VIDSP Parameter List24 DSP Type ListThis is a list of DSP types built into the Instrument.DSP Number DSP ID Type01 01H Equalizer02 02H Compressor

25.20 Piano Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45VII Setting Values and Send/ Receive Values

Note1: For information about the relationship between setting values and send/receive values, see “26.10 EQ Frequency SettingValue Table” in “VII Sett

Note1: For information about the relationship between setting values and send/receive values, see “26.4 –64 - 0 - +63 SettingValue Table” in “VII Sett

25.10 Auto PanParameter Number Parameter Name NotesParameter[1] LFO RateParameter[2] LFO DepthParameter[3] LFO Waveform Note1Parameter[4] Manual Note2

Note3: For information about the relationship between setting values and send/receive values, see “26.18 Vibrato/ChorusSetting Value Table” in “VII Se

Note4: For information about the relationship between setting values and send/receive values, see “26.20 Amp Setting ValueTable” in “VII Setting Value

Note1: For information about the relationship between setting values and send/receive values, see “26.23 Feedback TypeSetting Value Table” in “VII Set

Part VIISetting Values and Send/ Receive Values26 Setting Value Tables26.1 0 - 127 Setting Value TableReceive Value DSP Parameter Value Parameter00H -

26.6 Fine Tuning Setting Value TableTransmit Value Receive Value Parameter(LSB, MSB)(43H, 00H) (00H, 00H) - (5FH, 00H) 415.5 Hz(65H, 00H) (60H, 00H) -

26.10 EQ Frequency Setting Value TableReceive Value DSP Parameter Value Parameter00H - 05H 08H 100Hz06H - 0BH 09H 125Hz0CH - 12H 0AH 160Hz13H - 18H 0B

26.11 EQ Gain Setting Value TableReceive Value DSP Parameter Value Parameter00H - 04H 34H -1205H - 09H 35H -110AH - 0EH 36H -100FH - 13H 37H -914H - 1

Part IOverview1 Product Configuration as a MIDI DeviceAs a MIDI device, this Instrument consists of the System Section, Sound Generator Section, and Pe

26.14 LFO Wave Form3 Setting Value TableReceive Value DSP Parameter Value Parameter00H - 29H 00H Sin2AH - 54H 01H Tri55H - 7FH 02H Tra26.15 Polarity S

26.18 Vibrato/Chorus Setting Value TableReceive Value DSP Parameter Value Parameter00H - 11H 00H Off12H - 23H 01H V124H - 35H 02H C136H - 48H 03H V249

26.21 Pitch Setting Value TableReceive Value DSP Parameter Value Parameter(quarter tone)00H - 01H 28H -2402H - 04H 29H -2305H - 06H 2AH -2207H - 09H 2

26.22 Pitch Shifter Fine Setting Value TableReceive Value DSP Parameter Value Parameter(quarter tone/50)00H 0EH -5001H 0FH -4902H 10H -4803H - 04H 11H

26.26 Hex Layer Detune Setting Value TableTransmit Value Receive Value ParameterMSB- 00H - 03H 0- 04H - 07H 1: : :- 78H - 7BH 30- 7CH - 7FH 3126.27 Oc

Part VIIIMIDI Implementation Notation27 Value Notation27.1 Hexadecimal NotationMIDI implementation sometimes requires that data be expressed in hexade

Decimal Hexadecimal Binary0 00H 00000000B1 01H 00000001B2 02H 00000010B3 03H 00000011B4 04H 00000100B5 05H 00000101B6 06H 00000110B7 07H 00000111B8 08

Part number MIDI Receive Ch MIDI Transmit Ch Assigned Function(Note)01 1 01 - 16 Song Sequencer/Zone 1/SMF play/MIDI IN02 2 01 - 16 Song Sequencer/Zon

Part IIChannel MessageMIDI Message Send by Controller These MIDI messages can be sent by assigning any controlchange from CC:00H to CC:65H, after touc

Note: This Instrument has a function that assumes connection of an external device that sends Note Off Velocity as a fixedvalue. Note Off Velocity 00H is

Receive Receipt causes a change in the tone bank number stored in Instrument memory, but thetone is not actually changed until a Program Change messag