Casio BE-300 Spezifikationen

Pocket ManagerBE-300 (JX-740A)RSEP. 2001(without price)BE-300INDEX

— 8 —4. Orient the CASSIOPEIA in relation to the cradle as shown in the illustration below.5. Taking care to align the serial connector on the bottom

— 9 —Connecting the Cradle to a ComputerThe cradle has a USB cable for connection to a computer. Connect the end of the cable to a USB port of thecomp

— 10 —Using the CASSIOPEIA Serial CableYou can use the CASSIOPEIA serial cable to connect the CASSIOPEIA directly to acomputer.Important • Be sure to

— 11 —To remove the CASSIOPEIA from the PC Card Unit1. Make sure your CASSIOPEIA is turned off.• Press the [Power] button to turn off power.2. Pulling

— 12 —(2) System Status IndicatorsThese icons provide information about the system. Tapping an icon displays one of the settingscreens described below

— 13 —If unit power turns off due to sudden power drain by a CompactFlash card, the following warning messageappears on the display the next time you

— 14 —Remove the CASSIOPEIA from the cradle after charging is complete.The following illustration shows how to connect the AC adapter directly to the

— 15 —To change the sequence of Top Menu programs1. On the Top Menu screen, tap the name of the program you want to move.2. Tap Edit Move lcon.3. Sp

— 16 —Select the menu item for the type of settings you want to change.Selecting a Setup Menu ItemYou can use any one of the following methods to sele

— 17 —PasswordUse this screen to configure the CASSIOPEIA so it requires input of a password when it is turnedon. Data cannot be accessed unless the p

CONTENTS1. MAIN FEATURES ------------------------------------------------------------------------------- 12. SPECIFICATIONS---------------------------

— 18 —BrightnessThe brightness setting screen has three tabs named Contrast, Brightness, and Auto-Dim.Contrast TabUse this tab to change screen contra

— 19 —Note:You can also use the following button operations at any time to adjust screen brightness without displayingthe brightness setting screen.To

— 20 —Volume & SoundsThe Volume & Sounds setup screen has two tabs, named Volume and Sounds.Volume TabUse the settings on this tab to turn the

— 21 —PowerThe Power setup screen shows you remaining battery capacity. You can also use it to configure auto poweroff, which turns off the CASSIOPEIA

— 22 —Task Manager TabYou can use the Task Manager tab to shutdown a specific program that is running, or to shutdown allprograms that are running. Sh

— 23 —File ManagerFile Manager provides you with the tools to perform a variety of different operations involving files andfolders in main memory and

— 24 —To copy a file or folderNote:You can use the same procedure to copy a file or a folder. The following shows the procedure for copying a file.1.

— 25 —5. RESET OPERATION AND INITIAL SETUPReset OperationWhat does resetting the CASSIOPEIA do?Resetting your CASSIOPEIA is the same as restarting you

— 26 —What to do if resetting does not solve the problemPerform the following steps if resetting the CASSIOPEIA does not restore normal operation.1. W

— 27 —Initial SetupAfter you first unpack your CASSIOPEIA, perform the following initial setup procedure before using it for thefirst time.1 .Use the

— 1 —1. MAIN FEATURESBE-300 is a smaller and lighter CASSIOPEIA PDA compared with the prior ones.The main features on hardware are as follows;1. Highe

— 28 —6. BUILT-lN BATTERY PACK AND BATTERY REPLACEMENT6-1. Built-in Battery PackBuiIt-in Battery Pack Service LifeThough the built-in battery pack is

— 29 —7. DATA COMMUNICATIONS7-1. GeneralYou can connect your CASSIOPEIA to your computer and perform the types of operations listed below.• Synchroniz

— 30 —Communication PropertiesUse the Connect Setting dialog box to configure settings for the connection between your CASSIOPEIAand computer.To confi

— 31 —7-2. PC Connect softwareRequired System ConfigurationThe minimum system configuration required for running PC Connect software is described belo

— 32 —To install PC Connect software for PC and BE-300It is essential to install PC Connect software to your PC before performing Back up/ Restoreoper

— 33 —To connect, tap Connect Now button in BE-300 screen display referring to page 30 (To configure ConnectSetting).If succeeded in connection, you c

— 34 —7-3. Back Up and RestoreIf you want to store the user's data before repair, you should back up user's data at first withoutperforming

— 35 —Back Up / Restore using CF cardThe Backup program lets you quickly and easily back up all data (Calendar, Contacts, Tasks, and Mail data,files,

— 36 —5. Tap Backup now.• This causes the dialog shown below to appear.• If you do not wish to assign a password, go to step 6 without inputting anyth

— 37 —5. Tap Restore now.• This restarts the CASSIOPEIA, which is indicated by the message "Starting..." appearing on itsdisplay. Next, the

— 2 —2 . SPECIFICATIONSModel: BE-300Display: 240 x 320 dotsSTN Color LCD(32,768colors)CPU: VR4131 166MHz(280MIPS)Memory : ROM 16MB Flash ROM ( NAND Ty

— 38 —Back Up/ Restore using PC via PC Connect softwareIt is necessary to install PC Connect to PC before this Back Up/ Restore.You can obtain the fol

— 39 —RestoreYou can restore the CASSIOPEIA to either any backed up file state or the factory default state.Restore using backup fileThe following ste

— 40 —RestoreYou can restore the CASSIOPEIA to either any backed up file state or the factory default state.Restore to factory defaultThe following st

— 41 —To perform the actual back up using PC via PC Connect1. Turn off the unit.2. Connect the cradle or cable to PC installed PC Connect.3. Connectin

— 42 —8. Completing the backup, the following display will appear.9. Click OK according to the message.10. Extension of the backup files is .bin.To re

— 43 —6. Tap [PC Connection].• This establishes a connection between your CASSIOPEIA and computer. In response to the dialogbox that appears to ask if

— 44 —5. Start up your computer (which should have PC Connect installed on it), start up PC Connect,and establish a connection between the computer an

— 45 — 8. DIAGNOSTIC PROGRAM AND OPERATION CHECKTo abort the operation check, you must tap 13 Exit In Main Menu for the peration check. Tapping 13Exit

— 46 —Install the diagnostic programs to BE-300 according to the following procedure.1. Insert a CF card into the slot of BE-300. Doing so, BE-300 wil

— 47 —11. Clicking Add... button, and then input name "be300run".Doing so, the following display will appear.12. Clicking OK button, the fol

— 3 —Once Internal Battery Warning message appear, this message will not be disappeared even if the powersupply voltage becomes higher again.It is rec

— 48 —14. Clicking OK button, the following display will appear.15. Clicking Add... button, input CASIOconfidential folder in CASSIOPEIA, and then be3

— 49 —17. After clicking OK button, select Tools, and then Synchronize as shown below.Or click the icon for the synchronization.18. After completing t

— 50 —UUID Code is written and registered in EEPROM (lC3) only by the factory.Refer to SCHEMATIC DIAGRAMS and EXPLODED VIEW in this manual concerning

— 51 —8-3-3. Memory Check1. Tapping 3 MEMORY, the following display will appear.** Memory **1 BOOTROM CHECK SUM2 BOOTROM BUS CHECK3 NandFlashROM CHECK

— 52 —8-3-5. Audio Check1. Tapping 6 AUDIO, the following display will appear.** AUdio **1 0.5kHz2 1kHz3 2kHz4 LR-Channel5 Buzzer2. Connec

— 53 —5. Connecting PC Card Unit to the checking unit, PC Jacket Sw CLOSED display will be changed to PCJacket Sw OPEN.6. Pressing OK button, tap 2 Ke

— 54 —2. Supply DC 4.2 volt to the main battery terminal using DC stabilized power-supply instead of the mainbattery.To supply DC voltage, it is recom

— 55 —9. Pressing Top Menu button, the following display will appear.*** < AD Revision Value Write > ***< Max Level Write >AD Value Read!

— 56 —3. Pressing OK button, the following display will appear.The contrast value iswritten'4. Tapping Yes, this adjustment is completed.5. If yo

— 57 —Possible CauseThe touch screen is out of calibration.Static electricity or some other problem hascaused the touch screen to malfunction.The touc

— 4 —3. ACCESSORIES AND OPTIONS3-1. Bundled products and partsRefer to OTHERS in14. PARTS LIST and 15. EXPLODED VIEW in this manual concerning the bun

— 58 —Possible Cause Recommended ActionFollow the instructions that appear on thescreen.Internal malfunctionSome other warning message is on the scree

— 59 —Batteries lose powerAn icon in the system tray shows your current battery capacity. Be sure to recharge the battery as soon aspossible after it

— 60 —If you run out of CASSIOPEIA memoryMemory on your CASSIOPEIA is shared between storage memory and program memory. Storage memoryis used to store

— 61 —Screen is blankIf the CASSIOPEIA does not respond when you briefly press the Power button, press and hold the button fora full second, If that d

— 62 —Can dial out but cannot make a proper connection• Make sure the network to which you are trying to connect supports the Point-to-Point Protocol

— 63 —* SW2: for Detection of PC Card Unit EEPROM (IC3) CF Card slotCradle/ USB cableTimer clock32.768kHzX1IC1GATE ARAY (ASIC): RAKKO* RAKKO is a Japa

— 64 —11-1. MAIN PC BOARD ASSEMBLY(1/2)11. SCHEMATIC DIAGRAMSBuilt-inBattery Packfor LCDfor LCD driverBias VoltageAMPEarphone(To CF card)DC Power JACK

— 65 —11-2. MAIN PC BOARD ASSEMBLY(2/2)Detection for PC Gnd UnitTo the crade or USB cable2OK3 CURSOR DOWN4 ESC6 POWER7 CURSOR RIGHT8 CURSOR LEFT9 CUR

— 66 —11-3. CRADLE

— 67 —12. PCB VIEW (1/2)

— 5 —4. GENERAL GUIDEFixed IconSTap an icon to launch theprogram assigned to it.See the CASSIOPEIAUser's Guide for details.Top Menu buttonPress t

— 68 —PCB VIEW (2/2)

— 69 —13. DISASSEMBLY PROCEDURE1. Remove the flip cover and the stylusas shown to the right.2. Remove the dummy card as shown tothe right.3. Remove th

— 70 — 5. Remove the four screws securing thecases using the screw driver asshown to the right.There are four hooks shown witharrows in the right phot

— 71 — 8. Separate the upper case assemblyfrom the lower case assembly asshown to the right. You will be able toseparate by hand without using theopen

— 72 — 12. Disconnect the two FPCs and a flatcable from the connectors on themain PC Board as shown to the right. 13. Remove the two screws securing t

— 73 — 15. After disconnecting a flat cable fromthe main PC Board Assembly, removethe main PC Board Assembly asshown to the right.16. Remove the three

— 74 — 18. Disconnect the socket from theconnector on the inverter PC BoardAssembly as shown to the right. 19. Peel out LCD module as shown to therigh

14.PARTS PRICE LIST* Refer to the lower table concerning Applicable in Parts List.ApplicableShipmentU USA and Canada USA and Canada Type (AC 100~120V)

N Item Code No. Parts Name Specification Applicable Q Price Code RHARD COVER ASSY (C343993*1 TK)N161006 3017SPACERC445051-1Common2BYCN171006 3018SPACE

— 77 —15. EXPLODED VIEW15-1. PCB ASSY/MAIN (1/2)

— 6 —Removing the coverGently pull outwards on either of the cover hinges indicated by the arrows in the illustration until the hingeis free, and then

— 78 —* IC1/IC2/IC5/IC6/IC7 cannot be replacedbecause of BGA.* IC6/IC7 are the bare chip SDRAMs.Therefore, they are easily damaged.Item 5 is a plate/s

— 79 —* The diffuser for LED is strongly inserted into the trenchon the upper case.It is difficult to remove this diffuser.Keys are welded onto the up

— 80 —* After connecting AC adapter of item 31 to ACcord (item 33 ~36), supply the power to the unit.15-4. OTHERS (1/3)

— 81 —* German type* USA and Ccanada type* UK type* Australian typeOTHERS (2/3)

— 82 —OTHERS (3/3)

CASIO TECHNO CO.,LTD.Overseas Service DivisionNishi-Shinjuku Kimuraya Bldg. 1F5-25, Nishi-Shinjuku 7-ChomeShinjuku-ku, Tokyo 160-0023, Japan

— 7 —Adjusting Auto Dimming Settings1. Press the [Top Menu] button to display the Top Menu, and then tap Settings -Brightness .2. On the dialog box th